Professional Custom Lamp Holder Accessories Manufacturer

[2013-05-10]

GU10 lamp holder specifications (with a U-shaped pin pitch 10MM plug-in lamp) MR16 low voltage spotlights Specifications diameter 50MM) (GU5 .3 E27 lamp specifications (which is often said thread (Edison) Base) JCDR high-voltage spotlights Specifications Overall MR16MR11 spotlights Specifications (GU4 diameter 35mm)...

[2013-05-10]

The IEC60061/IEC62560 lampholders standard: The "G" of the GU10 lamp holder indicates the type of lamp holder is a plug-in, U lamp holder part of a U-shape behind the numbers that light foot hole center distance is 10mm, the GU10 is most common, of course, there are many other lamp, such as: GX6.35, GY9 .5, GY6.5, GX16D, and so on. The "10" of the GU10 lamp holder means that the two pins of the lamp holder distance is 10 mm, G means that the fixture is inserted into the formula, U, which means that the stitch shape of a "U" type ,GU10 lamp holders for high-voltage driver of lighting fixtures....

[2013-05-09]

MR11 and MR16 bulbs will both fit into the same connector since the terminal pins are 5mm apart on each. Two holes are drilled through the connector through which you can screw the connector into position on your wall or whatever. The bulb holder pictured above is now available: MR16 procelain Bulb Holder, as are compatible 12V LED spotlights.This halogen bulb socket fits G4, G5.3 and G6.35 bi-pin halogen bulbs. The socket has 18 inch wire leads. This halogen bulb socket can be used with most bi-pin halogen bulbs...

[2013-05-09]

Halogen Bulb Socket G4/G5.3 Base MR16 Lamp 12V : Use this wire connector socket to fit any MR16 or MR11 bulb into a hard wire system. It allows you to plug in your LED, CFL or halogen bulbs and attach it to normal lighting wires. (12v) 2-pin halogen lamps. Each pin...

[2013-05-07]

Block Down lamp holders installation: The power left some margin with the length of the maintenance penetrate the wire wooden desk or plastic stage, fixed with screws or self-tapping screws, wood or plastic table on the embedded parts, wood, brick or lamp box, available nylon bulge or plastic bulge fixed. Stripped wire leather, wire wear seat lamp, the distinction between the phase line and the zero line, screw lampholder reed should be connected to the phase line not to be confused with screw mounts lamp holder, the wires connected to the terminal screws on the get rid of excess wire, safety lamp casing, shade placement of shade, and the placement of the light bulb....

[2013-05-07]

Porcelain lamp holders insulation are the best insulation material in all materials, compared with the high temperature, bakelite, plastic temperature should be much higher degree of absolute flame retardant. Bakelite, plastic, easy to fire. Ceramic Absolutely not...

[2013-05-07]

Porcelain lamp holders producting process: Alumina powder into the plant in accordance with the requirements from different products with different molding process into a powder material was prepared. Particle size below 1μm microns The manufacture of high purity alumina ceramics in addition to alumina purity to 99.99%, the need ultra-fine grinding and make it uniform particle size distribution. Use Extrusion molding or injection molding, powder introduction of binder and plasticizer, generally the weight ratio of 10-30% of a thermoplastic plastic or tree....

[2013-05-04]

E12 LED and E14 LED light bulb lamp holders are typical of LED chandelier and LED night lights. EagleLight offers several types of LED candelabra LED bulbs including clear lens, frosted lens and LED torpedo lamps and LED flame light. Available in wattages that replace from 15W to 40W....

[2013-05-04]

The E26 is the standard 120 Volt American base. The E27 is the European variant and is rated at 220 Volts. E26 is 26 mm and the E27 is 27 mm diameter. However, an E26 bulb can fit in E27 base and an E27 bulb can fit in E26 base without problem. The sockets / bulbs are interchangeable except for the voltage rating. Therefore, LED E26 bulbs that are universal line-voltage can be used in both E26 and E27 lamp holders....

[2013-05-04]

This halogen bulb socket fits G4, G5.3 and G6.35 bi-pin halogen bulbs. The socket has 18 inch wire leads. This halogen bulb socket can be used with most bi-pin halogen bulbs. Remove the lamp (if not already out) from the socket or lamp holder. Examine the socket or holder electrical contacts. If they appear burned, discolored, oxidized, etc., gently scrape the contacts slightly until shiny metal becomes visible....